aivlasoft

Could be fixed and should no longer occur as soon as the next program version is available. Thanks a lot to Michael for helping me.

Stefan, The current version of the EFB is always using UTC as the time shown in the flightlog and on the top of the menu bar too. There is currently no way to change this behaviour, I'm sorry.

Michael, can you please send this route (or another example with the same behaviour) to support@aivlasoft.com. Once with the approach, and once without. Thanks a lot.

Ralf, can you please send the scenery.cfg and all the logfiles to support@aivlasoft.com? Thanks, and Merry Christmas

sorry, but then I wouldn't recommend to use this netbook.

Hi, if on the netbook the .net framework 3.5 SP1 is installed and the screen resolution is at least 1024 x 768 (better is 1024 x 1280), then it should run.

fixed with SP2

Mirko, Open the DataProviders settings. On the second tab (called 'Folders') you may select the option 'Create FSX flight plans ...' and then enter or select the folder which contains the FSX flightplans. Whenever you press the 'Activate' button in the 'RouteSetup' module, EFB is writing an FSX flightplan into the folder which you might have set as described above. If your aircraft is still on the ground, the flightplan will also be loaded into the Garmin 500 GPS. If you want the flightplan to be loaded also if the aircraft is airborne, then you must set the option 'Load flightplan to Garmin ... aircraft is airborne'. Please have look into the document 'Installation and Configuration Manual', section 'Configuration' on page 4 of 20.

Sabine, If you enter the DataProvider's path in the DisplayUnit settings the program verifies whether the data is already available in a correct manner. If this happen at a time where the DataProvider has not yet analyzed the FSX data you always get this red cross because the data obviously is not yet available. This is just to explain the circumstances.

Norbert, I assume that LDS means Level-D ? Is the FMC of the Level-D 767 able to read FSX flightplans? If so, EFB writes an FSX flightplan whenever you press the 'Activate' button in the 'RouteSetup' module. Just navigate to your FSX-flightplan folder an load it into the FMS. You may also create a *.rt2 file which is known by PMDGs FMC. Maybe this can also be read by the Level-D FMC? In the 'RouteSetup' press 'Save as *.rt2' file and then load it into the FMC. Hope this helps.

ahaka, I'm sorry for the inconvenience. The problem seems to be with the Com-Assignments. Did you change these assignments? Could you please send me the following file: c:\users\[username]\documents\AivlaSoft\EFB\Settings\DisplayUnitSettings.bin Another thing that attracts my attention is the missing city name at the top of the chart. It must be 'EFHK - Vantaa, Helsinki (Finland). The city name is also missing in all the COM-Frequency groups. It's quite interesting how did you manage this?

Bob, I just had a quick view into the source code and now I feel very embarrassed The problem you described can happen on other airports as well.

Bob, you're right, it's not correct to only show SIDs to the south at KDEN. It will be fixed in the next version 1.0.2.

William, thanks for the information about W7. Meanwhile the problem could be solved. It was an 'A380 add-on' which created some entries in the scenery.cfg that were missinterpreted by EFB. After an uninstall of this add-on everything is running perfectly now. The next version of EFB (service update) will have corrected this issue.

Cyrano, EDXW: You're right. After the insert of the values into the runway.txt file the ILS-32 approach should appear in the procedure selection window. I found that lousy bug ... Note: The Navigraph data for transition SLT into ILS-32 is wrong. Transition LANAS is ok. EDDK: I copied and pasted the values out of this topic into the runway.txt file on my computer. Then I saved the file and set the option "Always request airport data ...". I also set the option "Show Navigraph data identifiers ..." from the 'Charts-/Ground-Settings". Then I opened the Airport-Database and I selected the airport EDDK again. After getting the aiport data, I opened the 'Airport-Information-Window' from every chart-type (Arrival, Approach, Ground, Departure). On every window I can see all six runways (14L/32R, 06/24, 14R/32L).

Cyrano, will have a look on that today, just a question before: Did you install any add-on scenery for these two airports or is it still FSX-standard-scenery? Please have a look at > DisplayUnit > Settings > ChartSettings > Ground > "Show Navigraph data ...". Did you mean this?

solved with version 1.0.1.

solved.

Cyrano, I think this is the known problem that the data in FSX (which is the world you are flying in) is something about 5 years old whereas the Navigraph data is from today. The world is changing Please have a look into the 'Operations Manual', section 2, page 3, 'Messages on the DataProvider window'. You will find a detailed explanation how to solve such problems.

Xin, 1) is this already version 1.0.1? 2) could you please send all logfiles to 'support@aivlasoft.com'. The logfiles can be found as follows: Windows-Start-Menu > All Programs > AivlaSoft > EFB > Logfiles. Please send all files which can be found in that folder. 3) can you send me also the 'scenery.cfg', which can be found as follows: (Vista/Win7) C:\ProgramData\Microsoft\FSX\scenery.cfg (XP) C:\Documents and Settings\[username]\Application Data\Microsoft\FSX\scenery.cfg Thank you

Dave, you may send them all to the following e-mail address: support@aivlasoft.com many thanks

Philippe, just send (and send them all, please) to the following e-mail address: support@aivlasoft.com thanks,

Phillipe, could you please send me all the logfiles, which you will find as follows: Windows-Start-Menu, -> All Programs -> AivlaSoft -> EFB -> Logfiles. Thank you

Dave, could you please send me all the logfiles, which you will find as follows: Windows-Start-Menu, -> All Programs -> AivlaSoft -> EFB -> Logfiles. Maybe I can see anything 'between the lines' Thank you.

Dave, what text is the DataProvider showing on its lowest line?