No automatically closed

[mmaier41]

Hi,

 

The Manual says:

 

"SimpleCam is starting automatically with the respective option active and also automatically closed
upon closing the simulator."

 

No automatically closed by FSX on Windows 10.

 

Where can i look for clearing this problem.

[lonewulf47]

No problems here. I see it closing all the time, even most of the times after a crash of FSX/P3D. The only reason I could imagine is that there could be a conflict with UAC settings and/or Installation as Administrator. You should have the UAC set to the lowest level and the checkbox in the Properties Box set for "run as administator". Other than that I'm a bit at loss. Maybe someone else has another suggestion?

[mmaier41]

Hi Oskar,

 

many thanks for your answer

 

"UAC set to the lowest level" this was OK

"Properties Box set for "run as administator"" this was not set

 

After a System-Restart it seems to be ok.

[mmaier41]

Hi, Urs and Oskar,

 

i'm back again with the same problem.

 

Same times will be closed most not.

Otherwise i am very statisfied with the functionality specifically with the PMDG 737NGX.

[aivlasoft]

Hi Manfred,

 

is there any unusual behavior of FSX/P3D before you close it? If SimpleCam does not receive the 'quit' information of the simulator then it will stay open.

[mmaier41]

Hi Urs,

 

there is nothing no accident, nor anything else.

 

My normal Fly-Satus for FSX is with following ADDONS are active:

 

LINDA for control Saitek X52

ASN for weather

EFB for flyplane

PRO ATC-X for ATC and pre-flyplane

GTX groundservice

Accufeel for noise

 

and sametimes FS-FlightContol for Landing-Training ect.

 

All this addone's where not involved (not loaded) when i have checked this behavior.

I use two monitors M1=EFB and M2=FSX.

 

This is not vital, i will handle this by myself. two mouse click.

 

The Log shows two CLOSE-Situation. **********************************************************

 

2016-05-03 22:33:41.464 Debug    ------- SimpleCam started ------- *************** FSX gestartet jedoch Flug noch nicht gestartet System-Close [X] *****************
2016-05-03 22:33:41.547 Debug    Verify license
2016-05-03 22:33:42.510 Debug    License successfully verified
2016-05-03 22:33:42.571 Debug    Waiting for running simulator process ...
2016-05-03 22:33:48.116 Debug    Connection to simulator is established
2016-05-03 22:34:18.355 Debug    Simulator terminated by user      [X] ******** OK *******  
2016-05-03 22:34:18.384 Debug    *** SimpleCam terminated
2016-05-03 22:34:18.405 Debug    
2016-05-03 22:34:43.121 Debug    ------- SimpleCam started ------- *************** FSX gestartet und Flug gestartet - Pause - System Close [X] *****************
2016-05-03 22:34:43.198 Debug    Verify license
2016-05-03 22:34:44.184 Debug    License successfully verified
2016-05-03 22:34:44.249 Debug    Waiting for running simulator process ...
2016-05-03 22:34:49.811 Debug    Connection to simulator is established
2016-05-03 22:35:56.637 Warning    DefWndProc (isConnected=true): Ausnahme von HRESULT: 0xC000014B  [X] ********* nicht OK ***********
2016-05-03 22:36:29.877 Debug    UnsubscribeSystemEvents: COMException raised: Ausnahme von HRESULT: 0xC000014B  ***** SimpleCam User beendet *****
2016-05-03 22:36:30.005 Debug    *** SimpleCam terminated
2016-05-03 22:36:30.007 Debug    
 

[aivlasoft]

Hi Manfred,

 

thanks for providing the content of the logfile. The second one means that FSX closed irregular and therefore the connection to SimConnect was broken (0xC000014B means "Pipe broken", where a 'pipe' is an internal connection between two processes). As a result of this SimConnect could not send the 'quit' signal to SimpleCam. That's what I meant in my previous post.