MajorMike

Thanks. Today I ran the EFB2 Server and created a new profile. Now it is working. It has dawned on me that since I had installed the PMDG NGXu series I had not created a new profile. So obviously this has made the client now have the PMDG NGXu details. I am sorry to have troubled you with this. Regards, Mike Houghton

Thanks for the reply. yes I can . I have tried creating a new profile B737-800NGXu and although this appears on the list of profiles there is no green light and it still says default profile in the status box on the Client state.

When I run Aivlasoft EFB2 with PMDG v4.5 and the PMDG 737-800NGXu it comes up with a message in the Status box on the Client Page - Default Profile. A box opens asking me to create a profile for this aircraft. When I go to the Profile Editor there is no aircraft in the left hand side which has a green light next to it. So I can't seem to be create a new profile. If I load the PMDG 737-800NGX then it is recognised and it shows the correct aircraft in the Status box of the Client Page and if I open the Profile Page the B737-800 has a green light next to it. I have looked at the Client instructions but can't understand how I can create the profile for the PMDG 737-800NGXu. Please advise how I can create the profile. Thank-you. Michael Houghton

Thanks for the reply. I have resolved the problem. Because the Airbus A319 I used to make the views had IAE after it I used the simplecam file called A319IAE.simplecam file in the list at 'C:\Users\[Username]\Documents\Aivlasoft\Simplecam' to rename as A320.simplecam Tonight I tried to use the file just called A319.simplecam and renamed it as A320.simplecam. This has succesfully copied the views into the A320

I have P3Dv4.5 and the FS Labs Airbus A320 and A319. My version of simplecam is v1.1.14. I have today saved succesfully some views for the A319IAE and I thought I would put those view into the other versions of the FSLabs Airbus but I cannot find where it is saving the simplecam files. Is it stored outside the default place of C:\Users\[Username]\Documents\Aivlasoft\Simplecam? You will notice the simplecam file for the A319.IAE is not today's date suggesting the file has not been amended although I have amended the views and saved the views for the FSLabs A319.IAE today. Thank-you. Michael Houghton

Thank-you for that. The profile editor took a bit of finding but once I found it I have been able to sort this out. Regards, Mike

I usually fly airliners with programming of FMC and MCDU I am sure I have read and seen a picture that the TOC and TOD will appear in the A/C ambient column but I cannot get it to appear. I am sure I have read that all information has to be put into EFB2 correctly for it to appear. I am entering the flightplan which has been provided by PFPX. I have entered information including SIDs and Stars into the Wx and Proc buttons but still to no avail. Obviously I am missing something out. Is there a tutorial flight or is there any advice for this. Thank-you. Michael Houghton

Problem Resolved. I looked again at the other reference on this forum mentioning this problem I had tried moving copying the Microsoft sim Connect.dll from the redist folder in P3Dv4 to the Aivlasoft folder and copying and replacing the existing Microsift sim.connect dll. This did not help. After a further look I noticed Nicola mentioned(July 2017) you need to run the installer . I found the installer in the lib folder of the FSX-SP2_Xpack version in the redist\interface folder in the Lockheed Martin \P3Dv4 folder . It then worked. I must say I was surprised I had to run this installer assuming this would be already installed. Sorry to have troubled the forum with this Mike

I have run into a problem trying to install the Aivlasoft EFB v1_6_15 into Prepar3Dv4.2 on a Windows 10 64 bit computer. I have attached several screenshots . I have looked at the forum and tried the alternative Microsoft Flight Simulator .Sim Connect Files in the LM/P3Dv4/redist/interface/FSX-SP2-XPack without sucess. It appears to have come to a halt at Stop Sequence ..Please Wait. I have uninstalled the EFB and tried reinstalling wothout success. I have attached a copy of my simulator and Navigraph set up page in case this is wrong I have owned this program for several years and have not had a problem previously, On this computer i have not installed FSX. Any ideas would be appreciated. Thank-you. Michael Houghton

Hi Urs, Thanks for your reply. At last i think i have got it. I have succesfully imported the Simplecam views from PMDG 600-700. Thanks for all your explanation and patience which is much appreciated. Regards, Mike

Hi urs, Thank-you. I now have SimpleCam working in P3DV4. I now understand the air file allocated to each aircraft. However I tried copying the PMDG 737NGX 600 air file to the PMDG 737 NGX 700 folder and renamed the 600 air file 700 and it did not work. What have I done wrong.? Thank-you. Regards, Mike

Thank-you Urs. I note on my simplecam configurator there is no P3D V4 but presume this is because I have v 1.011 installed and the latest version is 1.013. Do I just install the latest version over my present install or do I have to uninstall and instasll the latest version.? Also please could you explain your final sentence. I do not understand whether I need to copy and paste files from my FSX SE into my P3D V4 to be able to use camera settings.? Also If I own the Aerosoft Airbus A319 and the A320 and I have made views for the A320 can I go to C\Users\My name\My Documents\Aivlasoft \SimpleCam and just copy the A320 SimpleCam file and rename the simple cam file A319 to enable views in the A319 ? Thank-you for your help. Regards, Mike

Hi Urs, Thank-you for your prompt reply. When I open the SimpleCam configurator there is no path to P3DV4 presumably because I have discovered I do not have the latest version of SimpleCam installed. Do I install the latest version over my existing installation or do I have to uninstall my existing installation and install the latest version? Please can you explain your last sentence about all camera settings in FSX SE being available in P3DV4. Do I have to copy and paste files for this? Another thing I am unclear on is if I have as an example the Aerosoft A320 and I make camera settings is there a way I can make those views available on the Aerosoft A319? Thank-you for your help. Regards, Mike

I have Simple cam installed on my computer working with FSX Steam edition. I have recently installed P3D v4 onto my computer. Do I need to install Simplecam again into P3D V4 or is it a question of telling Simplecam where P3D V4 is in the configuration manager? I would be grateful of clarification how I can get SimpleCam working in P3D V4. Thank-you. Michael Houghton